[wix-users] Wix Burn: Rollbackboundary was discarded?

[Farrukh Waheed]

So if I don't use RollbackBoundary for only 1 non-permanent package, would
it Rollback if I cancel its installation in the middle?

On 16 September 2015 at 17:16, Phill Hogland <phill.hogland at rimage.com>
wrote:

> I would expect NetFx451Redist and VC_ReDist_120 to be permanent.  If I did
> not have another package that was not permanent prior to the
> RollbackBoundary then I don't use a RollbackBoundry.  I only use a
> RollbackBoundary after other non-permanent packages, because of the issues
> that I have observed when all of the packages prior to the RollbackBoundary
> were marked as Permanent.
>
> -----Original Message-----
> From: wix-users [mailto:wix-users-bounces at lists.wixtoolset.org] On Behalf
> Of Farrukh Waheed
> Sent: Wednesday, September 16, 2015 2:28 AM
> To: WiX Toolset Users Mailing List <wix-users at lists.wixtoolset.org>
> Subject: Re: [wix-users] Wix Burn: Rollbackboundary was discarded?
>
> Hi Phil, Thanks for reply.
> Yes, both are marked Permanent. I will try without Permanent attribute then
>
> Regards
> Farrukh
>
> On 15 September 2015 at 17:53, Phill Hogland <phill.hogland at rimage.com>
> wrote:
>
> > Are both NetFx451Redist and VC_ReDist_120 marked to be Permanent?  I
> > have found that RollbackBoundary(s) do not play well when all of the
> > packages prior to the RollbackBoundary are permanent and there for
> > there would be nothing to uninstall if the setup rolled back to that
> > boundary.  I am not sure if my observation is related to your situation.
> >
> > -----Original Message-----
> > From: wix-users [mailto:wix-users-bounces at lists.wixtoolset.org] On
> > Behalf Of Farrukh Waheed
> > Sent: Tuesday, September 15, 2015 5:13 AM
> > To: wix-users at lists.wixtoolset.org
> > Subject: [wix-users] Wix Burn: Rollbackboundary was discarded?
> >
> > While compiling Burn project I'm getting following warning:
> >
> > MyBundle.wxs(111,0): warning LGHT1129: The RollbackBoundary
> > 'rba6ABCDA022AB9852FA39D23549E335DF4' was discarded because it was not
> > followed by a package. Without a package the rollback boundary doesn't
> > do anything. Verify that the RollbackBoundary element is not followed
> > by another RollbackBoundary and that the element is not at the end of
> > the chain.
> >
> > And here is my chain:
> >
> > <Chain>
> >   <PackageGroupRef Id         = "NetFx451Redist"  />
> >   <PackageGroupRef Id         = "VC_ReDist_120" After="NetFx451Redist"
>  />
> >
> >   <RollbackBoundary />
> >   <MsiPackage      Id         = "MainProduct"
> >                    DisplayName             = "$(var.ProductName)"
> >                    DisplayInternalUI       = "no"
> >                    Visible                 = "no"
> >                    Compressed              = "yes"
> >                    SourceFile              = "$(var.MainProduct)"
> >                    Vital                   = "yes"
> >                    After                   = "NetFx451Redist"
> >                    InstallCondition="NETFRAMEWORK45 >=
> > $(var.NetFx451MinRelease)">
> >     <MsiProperty
> >         Name                  = "DIR_PROGFILES_64_VA"
> >         Value                 = "[DestinationDir]"/>
> >   </MsiPackage>
> >
> > *Question:* So what's wrong with this RollbackBoundary here?
> >
> > Thanks
> >
> > Farrukh
> >
> > ____________________________________________________________________
> > WiX Toolset Users Mailing List provided by FireGiant
> > http://www.firegiant.com/
> >
> > ____________________________________________________________________
> > WiX Toolset Users Mailing List provided by FireGiant
> > http://www.firegiant.com/
> >
>
> ____________________________________________________________________
> WiX Toolset Users Mailing List provided by FireGiant
> http://www.firegiant.com/
>
> ____________________________________________________________________
> WiX Toolset Users Mailing List provided by FireGiant
> http://www.firegiant.com/
>